Pictures of your airsoft rifle

[cmdrfire]

Pics of my recently revised M16 SPR... now with spiffy systema and prometheus internal goodness, that PVS-14 and a bipod...

http://www.cmdr-fire.co.uk/images/airsofting/m16_spr.jpg[/img]
http://www.cmdr-fire.co.uk/images/airsofting/m16_spr_2.jpg[/img]

That is just awsome!
I am thinking of turning my m15a4 into a SPC/SPR but I was wondering how do you remove the barrel. I unscrewed the small nut under it , but was wondering if I have to move or unscrew the handguard release thingy(name elude me now! ) or could I just pull that thing off? Thx in advance...

Thanks bud!
Do you mean the RAS itself or what?
The M5 RAS should be pretty easy to remove, just remove your triangle site (knock the two pins at the bottom out, and knock out the pin holding the gas tube in, and slide it out...), remove the lower part of the RAS and then the upper part... I'm afraid I don't know about the inner barrels though, haven't ever dealt with a CA gun before.

[stuntman]

Pics of my recently revised M16 SPR... now with spiffy systema and prometheus internal goodness, that PVS-14 and a bipod...

http://www.cmdr-fire.co.uk/images/airsofting/m16_spr.jpg[/img]
http://www.cmdr-fire.co.uk/images/airsofting/m16_spr_2.jpg[/img]

That is just awsome!
I am thinking of turning my m15a4 into a SPC/SPR but I was wondering how do you remove the barrel. I unscrewed the small nut under it , but was wondering if I have to move or unscrew the handguard release thingy(name elude me now! ) or could I just pull that thing off? Thx in advance...

Thanks bud!
Do you mean the RAS itself or what?
The M5 RAS should be pretty easy to remove, just remove your triangle site (knock the two pins at the bottom out, and knock out the pin holding the gas tube in, and slide it out...), remove the lower part of the RAS and then the upper part... I'm afraid I don't know about the inner barrels though, haven't ever dealt with a CA gun before.

na I ment the locking ring that holds the barrel. it has a star shaped to it and in order to get to it you have to move the forgrip holder back. I am not good with discribing some parts so please bare with me.. Thx!

[Rebel Yell]

Here it is my preferred ASG:



Colt M933
- Marui based
- Systema M4A1 Metal Receiver & Hop-up
- Guarder Handguard (9.6 1700 fits in)
- ICS "LE" Stock
- ICS QD Short Silencer
- TGS Aimpoint COMP ML-2 Replica + M68-ARD KillFlash

Internals:
- HurricanE 6mm gear-box
- Guarder metal bushings
- Systema "standard" gears
- Systema Genuine motor
- Custom 1j spring (around 330FPS)
- Systema A1000 Spring guide
- Systema Teflon cylinder & silenced piston head
- Systema Aluminium piston
- Guarder Tappet-plate & Air-Nozzle
- KM HEAD Precision barrel 6.03mm
- Silicon wires (fuse has not been removed)

And here without silencer and other accessories...

[Rebel Yell]

I don't know if the following pics are shown (I can see them):

VSR-10 G.Spec


Cheekpiece and front rail are Smokey's + Harris Bipod and Royal Scope.
Internals: all Laylax (various springs up to 480FPS)

M4 RIS


Marui based with all upgraded internals. G&P one-piece outer barrel, ICS "LE" Stock has been added later on (the above is the original one) and custom sping (390FPS, high-speed gears). HurricanE metal receiver (I wanted a "grey one")

MP5 Kurz


Narui. All internals upgraded with Systema parts (high-speed gears). ICS low-rail with BSA 40mm red dot. G2 Surefire w/ original H&K front mount. Guarder MP5-S Silencer. A 9.6 600mAh fits in (modified).

AK-47 Beta-S


Marui. All internals upgraded with Systema parts (high-speed gears, M100 spring, KM barrel and other stuff... 350FPS). Dot and silencer are the same you can see mounted on the Kurz. Front rail is the Othomo 3-points.

MP5 S-RAS


Marui. A very easy piece for training. Lightweight and all-purposes: based on a very old Marui MP5A5, I've added fixed stock (Classic Army), Marui RAS, threaded flash-hider with MP5-S silencer. Marui rail + Guarder Reflex dot sight. Internals are almost original: I've installed Classic Army bushings, Systema piston head (A1000) and 1j Spring (it comes out @ 300FPS).

[Lone]

painted my g36C today

[tenda]

really nice guns rebel yell...
and really good paintjob lone...

[Mongoose_nl]

Very nice paintjob Lone...........

Echt supervet gespoten!!!

What kind of paint did you use?

[Lone]

Very nice paintjob Lone...........

Echt supervet gespoten!!!

What kind of paint did you use?

thanks

As a primer i used a 'kunstof-primer' from Motip.
For the colours I simply used the little Tamiya paint cans that you can get at the local 'modelbouw' winkel
I finished it off with matt varnish, also from Motip

[Ryan94]

Yes, that's really a great paintjob, just get a G36K and the rifle will be perfect...

[Mongoose_nl]

....For the colours I simply used the little Tamiya paint cans that you can get at the local 'modelbouw' winkel

This means you used a paint brush?

[Lone]

....For the colours I simply used the little Tamiya paint cans that you can get at the local 'modelbouw' winkel

This means you used a paint brush?

no, i didn't use a paint brush.
I just used those little spray cans
I'll take some pics tomorow if you want.

Ryan94, I was going to paint my G36E kit too, but i ran out of paint
I'll go to the shop next saturday and buy some more

[Mongoose_nl]

..no, i didn't use a paint brush.
I just used those little spray cans
I'll take some pics tomorow if you want.

I see....I think they are same as I used for my ICS M4.
Could you give me numbers of those spray cans?

[berkal]

M15A4 SPC
OD furniture
PEQ4 clone (IR modified model)
Aimpoint on KAC Railgrabber
PVS14 on ARMS #175 (and, yes, before anyone asks...it is real )

[Carbine]

I wish I could afford a PVS-14, but just can't justify dishing put over 3g for a sight

[Scottie]

lol i wish i knew more about sights and stuff... coz i have no idea why i have on sight looking into another??

is there maybe a general website about sights and all that stuff, with all the different types etc.